SmartAdhesives

i2 Instant Adhesive - Thick Liquid

i2 Instant Adhesive - Thick Liquid

  • All-purpose, sets in 20 seconds

  • No ordinary super glue

i2 Instant Adhesive is the high viscosity version of our all-purpose line of cyanoacrylate adhesives. i2 is a very fast setting, single component adhesive with a viscosity similar to 10 weight motor oil. Apply a thin layer of i2 to well-fitting metal, plastic, rubber, or ceramic parts to create a strong assembly. For stronger bonds, i2 is formulated with a higher concentration of active ingredients than consumer grade instant adhesives ("super glues").

Recommended Substrates

  • Glass & Ceramics
  • Metal: Aluminum, Nickel, Stainless Steel
  • Metal: Steel, Copper, Galvanized Steel, Chromated Steel
  • Plastic: Polyethylene [HDPE, LDPE], Polypropylene, Acetal, Nylon
  • Plastic: Acrylic, ABS, Polycarbonate, PVC, Styrene
  • Plastic: Composites, Fiberglass, Epoxy, Phenol, Polyester
  • Rubber: EPDM Rubber
  • Rubber: Latex or Synthetic Rubber

Industries & Uses

Technical Materials

Performance

  • Shear strength

    2,291 psi (steel-steel)

    i

  • Service temperature

    -60 to 180 degrees F

    i

  • Impact resistant

    No

    i

  • Water resistant

    No

    i

  • Solvent resistant

    No

    i

Cured properties

  • Color when dry

    Clear

    i

  • Dries transparent

    Yes

    i

  • Can be painted/stained

    Yes

    i

  • Fills gaps

    No

    i

  • Removable

    No

    i

  • Flexible

    No

    i

  • Rigid

    Yes

    i

Liquid properties

  • Form

    Thick liquid

    i

  • Non-drip

    No

    i

  • Low/no VOCs

    Yes

    i

  • Viscosity @ 77°F (25°C)

    500 cP

    i

  • Worklife

    20 seconds

    i

  • Set time

    20 seconds

    i

  • Full cure time

    24 hours

    i

  • Shelf life

    12 months

    i

  • Cure method

    Evaporation

    i

  • Application temperature

    60 - 80 degrees F

    i

Handling

  • Number of components

    1

    i

  • Mix ratio

    No mixing required

    i

  • Application methods

    Bottle

    i

Application instructions

DIRECTIONS: Clean surfaces to remove all dust, dirt and grease. For highest bond strength, chemical cleaning is advised (use acetone or isopropyl alcohol, depending on substrate). Apply sparingly and spread adhesive thinly and evenly on surface. Immediately join surfaces together with firm pressure until adhesive sets (approx. 20 sec. @ 70˚F). Replace cap when not in use. Store in cool, dry place away from direct sunlight. Refrigeration preserves shelf life. Do not use as medical aid.

OPENING 1oz. & 2oz. BOTTLES:
To open the bottle, use a pin or needle to pierce the tip.

Always test on samples to determine suitability.

Safety Information

PRECAUTIONS: Combustible. Avoid contact with eyes and skin. Bonds skin instantly.

SUGGESTED FIRST AID: Eye Contact: Immediately flush eyes with plenty of water. Do not force eyelids open, seek medical advice. Skin Contact: Immediately soak in warm water. If fingers are bonded, use rolling, peeling motion. Do not pull. If unable to free stuck skin, seek medical advice. Inhalation: Move to fresh air. If symptoms develop, seek medical advice. Ingestion: Do not induce vomiting. Seek medical advice.

Shipping information

Shipping Weights

  • i2OZ1 (1 oz. plastic bottle): 0.4 pounds
  • i2OZ1CASE (CASE of 10 - 1 oz. bottle): 1.5 pounds
  • i2OZ2 (2 oz. plastic bottle): 0.5 pounds
  • i2OZ16 (16 oz. plastic bottle): 1.6 pounds


Shipping weight is the total weight of the product, including the box and packaging required to safely ship the item.

Notes

 

Find Your Adhesive

Connect this...
To this...

Optional Narrow your results:

No Results 0 adhesives

Please change your selections at the left